Story

Ariston has supplied a GENUS HE 30kW combination boiler which is providing heating and domestic hot water for JSB.SWIM’s new teaching pool facility. Jackie Butler has been teaching swimming for over 15 years and last year invested in a new, purpose-built, 6.8m x 3.3m pool adjacent to her home in the Beacon Hill area of Newark. Here, she teaches swimming to all ages, from babies to adults including special needs and, with wheelchair access to the pool and changing facilities, can also accommodate pupils with disabilities.

The SEDBUK Band A rated GENUS HE 30kW boiler was selected by Cooper Plumbing of Mansfield due to its build quality, high level of energy efficiency and the excellent back-up provided by Ariston. A spokesman commented: “We have fitted a number of these boilers in the past and have always been highly satisfied. We have found them simple to commission and have had absolutely no problems with them once fitted.” The boiler supplies space heating, via an air handling unit and radiators, as well as hot water to the pool, the changing room shower and the wash hand basin in the separate toilet. It is located in the plantroom which adjoins the pool room and is fitted with a rear-facing. room-sealed, fanned flue. All Ariston boilers are designed to be completely adaptable to every possible flue situation, with a wide range of flue pipe accessories available.

The GENUS HE boiler offers a number of significant operational benefits not available with other central heating boilers on the market: the energy saving AUTO function, which provides energy savings greater than those normally associated with high efficiency boilers; the sophisticated TIMER function, the INFO function showing status, history and diagnostic information in clear scrolling text and the COMFORT function which provides almost instantaneous hot water.

The AUTO Function provides intelligent management of the indoor temperature by automatically selecting the ideal temperature for the central heating circuit, gradually increasing the temperature of the system water and eliminating peaks in the flow until the room reaches the desired temperature. Temperature control is therefore achieved smoothly, without turning the boiler on and off, eliminating thermal stress and resulting in higher levels of energy efficiency.

GENUS HE’s digital TIMER function allows the user to set the operating period via 24 hour and 7 day programmes in 15 minute bands, with two zone temperature management as standard. Digital status indication, operating history and diagnostic error information generated by the INFO function is displayed on an LCD screen on the front of the boiler, making it particularly user-friendly. This function also allows the installer to key in his contact details for call-out and maintenance purposes. The COMFORT function delivers almost instantaneous domestic hot water by using the pre-heat process, reducing the waiting period to just 5 seconds.

In addition to SEDBUK Band A rating, indicating maximum energy efficiency, the GENUS HE boiler range also features, low NOX and an impressive 5 year guarantee as standard. Whilst operating with a simple room thermostat in this installation the GENUS HE range is compatible with a wide range of accessories. When used in conjunction with the AUTO function these products result in even higher levels of energy efficiency.

View Ariston's profile:

Story

New from Thorn, unique in its styling, Adelie is a highly distinctive post top mounted luminaire. It combines a ring of 32 x 1.1W LEDs with a funnel shaped canopy to create a soft indirect light in parks and building surrounds.

Adelie is crafted from sandy grey aluminium with a white reflector to direct the cool light (5300K) down without glare. The surface is Teflon-coated, to ensure that it remains both water and stain repellent (sealed to IP65).

The circular LED compartment has a ribbed base, with distinctive red decoration ring, to dissipate heat and prolong life (up to 50,000 hours). It is topped with a PMMA lens, inclined to allow water run off.

A dedicated 3m tapered aluminium column blends perfectly with the lantern continuing the design theme through column and lantern. The slim section control gear, pre-wired with 3.5m cable, is positioned in the column base to save depth and allow easy access.

It is these features that help the Adelie blend especially well with modern architectural styles. From a distance the lit shape is similar to a ‘flying saucer’ that appears to hover in space.

View Thorn Lighting's profile:

Story

Enhanced testing safety, even in demanding applications, is offered by the latest versions of the MIT and S1, 5 kV and 10 kV Megger insulation testers. All models now meet the requirements for use in CAT IV 600 V applications, in line with IEC 61010–1.

This means that the new instruments are suitable for performing measurements at the source of supply in low–voltage installations and offer immunity to high–voltage transients up to 8 kV – double the rating of their predecessors.

Another crucial benefit is that, for instruments of this class, Megger is the only supplier to fully specify the performance of the guard terminal. This specification shows that, unlike many of its competitors, Megger has achieved these important safety enhancements without compromising guard terminal performance.

As a result of this, combined with the high current capability of the testers, users can be sure of achieving fast, accurate results even in the presence of high levels of surface leakage in the equipment under test. This is important as it enhances the ability of the instrument to provide reliable information to assist in the diagnosis of faults.

Megger has also upgraded the PC based software supplied with the instruments to the latest Power DB Lite package. This allows test results to be loaded directly into test forms and certificates that are uniform in layout and appearance with the test documentation produced by many of the other power instruments in the Megger range.

Megger high–voltage insulation testers offering CATIV 600V capability are the MIT510/2 5 kV insulation tester, the MIT520/2 5 kV diagnostic insulation tester and the MIT1020/2 10 kV diagnostic insulation tester, along with their high–current S1–range counterparts, which deliver a test current of up to 5mA compared with 3mA for products in the MIT range.

The CATIV 600V rating also applies to the S1–554/2 5 kV high noise immunity tester and S1–1054/2 10 kV high noise immunity tester, which are particularly well suited for use in substation switch yards and other areas where extremely high levels of electrical noise may be present and S1–552/2 5kV high current tester and S1–1052/2 10 kV high current tester which as designed to cope with capacitive loads

To complement the new versions of its insulation testers, Megger is now supplying them, as standard, with insulated test leads rated at 5kV or 10kV depending on the type of instrument. Compact uninsulated crocodile–clip style leads continue to be available as an option.

View Megger's profile:

Story

Baxi Commercial Division has donated two Potterton Commercial high efficiency condensing boilers for the recent redevelopment of St. George’s Crypt, one of the UK’s foremost homeless charities. A £1.5 million redevelopment at the Crypt’s main site at Great George Street, Leeds has provided refurbishment of the existing facilities, together with an extension. The new facilities include a number of individual bedrooms, a new reception area, modern training rooms for personal and life skills, a residents’ lounge and an expanded and refurbished restaurant with a new kitchen. This project has been made possible thanks to donations from charitable trusts, companies, private individuals and the Government’s Homes and Communities Agency which has granted almost £1million to the project.

The two Paramount two 95kW boilers were selected by KSP Consulting and a spokesman commented, “As space within the Crypt is very limited we chose the Paramount two boilers because they are high output, compact and are wall mounted. In addition they are very efficient with fanned flues.” The boilers serve steel panel radiators throughout the existing Crypt area, the newly modified areas and the new extension which has been added to the side of the Crypt and Church. Additional efficiencies have been achieved by locating the boilers in a new plantroom nearer to the radiator circuits, which has reduced the amount of distribution losses. The existing boiler has been maintained to serve the Church. Building services were installed by Ellison Energy Ltd. and the main contractor was Baum Construction Management Ltd.

The Paramount two range of wall-hung condensing boilers feature state-of-the-art heating technology with a combustion system which delivers energy efficiency levels up to 109% net as well as ultra low NOx which exceeds Class 5. These boilers have pre-mix, fully modulating control for complete heating flexibility and the aluminium/silicon alloy heat exchanger carries a lifetime guarantee. A user-friendly control panel with full text display of operational status avoids the inconvenience of checking codes or lights. Other features include inbuilt weather compensation, summer/winter changeover and time control facilities. The advanced ISR control system in this case operates with a simple room thermostat, with a remote control panel, although it can also be used with a fully integrated Building Energy Management System. The Paramount two boilers are available in six sizes, from 30kW to 115kW.

For 80 years, St George's Crypt has offered care and shelter for homeless and needy people in the Leeds area and this latest project will enable it to offer even greater support. Modern training rooms offer courses in art and crafts, debt management and literacy, whilst the new lounge means that residents no longer need to leave the premises after each meal, as was the case previously. An IT suite is due for completion soon and this, together with the other new facilities, will enable the Crypt to place a greater emphasis on rebuilding the lives of clients, many of whom have drug and alcohol dependency issues and/or mental health problems.

View Potterton Commercial's profile:

Story

One of the main distributors for Beko products has been involved in fitting out two new student accommodation buildings at The University of Reading, acting as a one-stop shop for the supply, wiring and pre-commissioning of all the appliances within 122 'cluster kitchens'.

JPD Contracts, based in Coalville, Leicestershire, provides a nationwide service, supplying housebuilders and main contractors with the full range of white goods and other appliances. In the case of The University of Reading's Stenton and Mackinder Hall buildings Morgan Sindall was the main contractor.

Each individual kitchen was equipped with a Beko oven, hob, extract hood and an upright fridge-freezer. As is normal on contracts of this scale, JPD worked with the rest of the project team on the creation of prototype kitchen which the university's architect and property management department could inspect and fine tune.

The Managing Director of JPD Contracts, John Evans, comments: “We have been dealing with Beko for some three years now and will have seen our business with the manufacturer grow by 30 per cent in the past year. Not only do we get good service from Beko, but they are the right products at the right price for the current market.”

“Beko's commitment to product reliability, a dependable delivery programme and technical support is a real asset to us”.

“Our client base includes the UK's top 10 housebuilders while we work extensively with the public sector, and Reading University is just one of a number of student accommodation contracts we have completed recently in conjunction with Beko.”

“The appliances are delivered to our main distribution warehouse and then our teams of fitters take them to site where they then gas, wire and pre-commission everything before taking away the packaging and any rubbish. Stenton Hall had 50 cluster kitchens, and Mackinder 72, done in three and six phases respectively, where we had up to four teams working at any one time.”

The University of Reading project was completed and handed over ready for the start of the current academic year.

View Beko's profile:

Story

REHAU's PE-Xa pipework has been used in an innovative new project for Telford & Wrekin Council which will deliver energy savings for the redeveloped Wellington Civic and Leisure centre.

Part of an £8.5m town centre redevelopment, the building is being extended by 3,300m2 and will house two floors of council offices, as well as a swimming pool and leisure centre, library and café.

The Council's Property and Design department has worked closely with Interseasonal Heat Transfer specialists ICAX to design a sustainable heating solution for the new centre which minimises both energy losses and running costs and helps the building to achieve an EPC A rating.

A 20 borehole field has been installed in front of the building to create a ThermalBank which will store in the ground excess ‘free heat’ generated during the summer from solar roofing, solar chimneys, swimming pool and changing room ventilation for use during the winter.

REHAU has an established partnership with ICAX so supplied the RAUGEO 40mm PE-Xa probes for the 20 boreholes, which were each drilled 100m deep by Terra Firma GI.

REHAU PE-Xa header pipe was installed to connect the boreholes and Mark Bradley of Terra Firma GI estimates that the connection using REHAU's Everloc compression joint system took less than half the time it would have taken using the alternative PE electro-fusion fittings and PE 100 pipe.

The 30m x 10m x 100m deep ThermalBank will be connected to an ICAX Skid, which will extract heat using heat pumps when required for use in the winter to heat the building. When there is a requirement for heat, the ICAX Skid unit will analyse where it can be delivered from most efficiently and activate the appropriate heat source.

The Wellington Civic and Leisure centre, part of the council's borough town imitative programme, is scheduled for completion during 2011. The main contractors are GF Tomlinson.

View Rehau's profile:

Story

Andrews Water Heaters, part of Baxi Commercial Division, has supplied two SOLARflo water heating systems, along with Queen’s Award winning MAXXflo condensing water heaters, for the new Beacon Centre for the Blind in Wolverhampton. The centre brings together services for people with sight loss which were previously housed in eight separate buildings on the seven acre site. Some of these were in need of refurbishment and all were expensive to maintain and run so, after due consideration, the decision was taken to replace them with a brand new centre. The new state of the art facilities comprise a three storey office block and a separate support area to the residential block which have both been designed to achieve an energy efficient solution which minimizes CO2 emissions.

The whole Building concept scheme with the two SOLARflo systems were specified by Rediger Ltd., who are CIBSE registered Low Carbon Consultants. A spokesman commented, “We have used this equipment in the past and Andrews have a good reputation in this respect. The system comes as a complete package and the inbuilt controls provide all that is necessary for efficient operation. I n addition, there were no problems tying in with the BMS.”

Matched equipment from a single source, together with the availability of technical advice throughout the installation, is a particular benefit of the Andrews Water Heaters product range and after sales service.

The SOLARflo system serving the office block provides domestic hot water to washroom facilities and kitchenettes on each of three floors, a total of 24 wash hand basins and five sinks. In the residential support building, the system serves a kitchen with four outlets, a bar with two sinks, a hairdresser’s with four basins and two toilet areas with a total of eight wash hand basins. Both systems were designed and installed by William Davis Ltd. and a spokesman commented, ‘Everything went well from initial concept to completion of the project’.

The office block system comprises six roof-mounted, glazed flat plate solar collectors with a total area of 15.6 square metres, a 900 litre twin coil cylinder and a MAXXflo CWH120/300 condensing storage water heater. The MAXXflo water heater, cylinder and other components of the solar package are installed in the ground floor plant room, where the water heater is installed with a horizontal, balanced flue. The residential support block has seven roof mounted solar collectors with a total area of 18.5 square metres. A 700 litre twin coil cylinder, a MAXXflo CWH 60/300 water heater, with vertical balanced flue and the remainder of the solar package are again installed in a ground floor plant room. These high efficiency, gas-fired, condensing storage water heaters each have a capacity of 300 litres and recovery rates through 50oC of 1020 litres per hour for the CWH 60/300 and 2040 litres per hour for the CWH 120/300 which is the largest unit in the MAXXflo range.

Water is preheated by the glazed flat plate solar collectors, which have a transmission efficiency of 90.8%, an absorption efficiency of 95% and a low emission loss of only 5%. Heat is transferred to the two twin coil cylinders which in turn pre-heat the supply to the MAXXflo water heaters, thereby considerably reducing consumption of natural gas. In addition to the solar collectors and non-corrosive, stainless steel solar cylinders the complete SOLARflo package also includes solar controls, pump station, expansion vessels, first fill of heat transfer fluid and collector mounting accessories.

The MAXXflo range of high efficiency, condensing, gas-fired storage water heaters has won the Queen’s Award for Innovation for it’s energy saving capabilities. These units are therefore ideal for buildings with a high demand for hot water and, thanks to their fast recovery rate and innovative design, carbon footprint, NOx levels and running costs are kept to a minimum. MAXXflo storage water heaters incorporate a fully modulating burner to provide maximum performance and flexibility, using condensing technology to achieve an operational efficiency of 109%. Heat input and flow are carefully regulated to produce a closely controlled water temperature and a high temperature anti-Legionella program is incorporated as standard.

Editor’s Note

The Beacon Centre for the Blind in Wolverhampton helps local people with sight loss to live fuller and more independent lives by offering them the finest facilities and support, including a mix of residential, day care and community services. Formed in 1875 as the Wolverhampton Society for the Blind, the current name was adopted in 1991 and, in 2003, the former individual workshops on the site were eventually closed. The decision to redevelop the site completely was taken against the background of Government forecasts which predict a rise of 35% in visual impairment by the year 2020, due to an ageing population and the prevalence of diabetes.

View Andrews Water Heaters's profile:

Story

View Eaton Electrical's profile:

Story

Part M of the Building Regulations 2000 (access to and use of buildings) is designed to make it as easy as possible for all persons, regardless of ability / disability, to enter and use buildings and the facilities within them. This requirement applies to the wiring accessories contained in the buildings as much as the buildings themselves, and will apply to all non-domestic new-builds as well as any modifications carried out to existing, non-domestic buildings. Crabtree has therefore been introducing products throughout its range of wiring accessories to enable compliance with Part M. It is important to realise though, that just using the products themselves does not ensure conformity.

With Crabtree, however, these products do help to make the job of the contractor as easy as possible. For example, a high contrast between a front plate and its corresponding background makes it easier for everyone to find the switches, while in particular providing valuable help for those with limited eyesight. The Crabtree solution also helps save money and resources especially for refurbishments, as there are many upgrade solutions, like replacement power outlet or switch surrounds, which avoid having to replace an entire wiring accessory.

To help the visually impaired, products meeting Part M standards should also clearly indicate whether they are ‘on’ or ‘off’ – Crabtree use red flashes in the switch rocker and neon indicators, the latter proving particularly useful at night or in low-light conditions.

Light switches, which are to be used by the general public, are encouraged to have large push-pads, a feature available on the majority of Crabtree accessories, and they should be at door-handle height. This obviously makes it as easy as possible for those people with a physical disability or visual impairment to locate and activate them, and is backed up by the suggestion that these larger push-pads mean that a fist or elbow would be able to operate them as easily as a finger. Couple this with Seeklight perimeter illumination for light switches, and it becomes easy to identify their location, even in the dark.

The ‘ease-of-operation’ aim that these requirements propose extends to ranges of components using multiple switches. Part M stresses that multiple switched components should always be ‘well separated’. This means that all visitors should find it easier to avoid inadvertently selecting an adjacent control; an example being the highly popular Crabtree Capital switched socket outlets, which can be ordered with outboard rockers – making it virtually impossible to accidentally activate the wrong socket outlet. Rockergrid, which is a modular system of boxes grids, plates and switches, can quickly and easily be assembled to customers’ specifications, enabling several circuits to be controlled from a single location. The switches have large concave rockers with barriers between each one to avoid inadvertent selection of adjacent controls.

The features and requirements laid out by Part M in the vast majority of cases only provide guidelines. This means that the contractor and developer have to ensure that the installations that are carried out meet with these guidelines, and both are expected to use their own judgement to ensure that any components chosen do not fall outside the scope of Part M. It is because of this that Crabtree have ensured that their products can meet with the vast array of variables set out by Part M, making this difficult task as easy as possible.

When it comes to specifying electrical wiring accessories that comply with Part M, there is a wealth of products that meet with the requirements contained in the guidelines. Crabtree, in particular, has a vast and extensive portfolio of products ranging from specially designed switches and sockets to contrasting replacement components. All these features of the Crabtree range are there to benefit the specifier and contractor in making the best choice when it comes to meeting the requirements laid out in Part M.

For further assistance, Crabtree have produced a handy printed guide, together with literature detailing their PartM compliant product range. For your free copy please phone 01543 455030 or circle the reader link card at the back of this magazine.

View Crabtree's profile:

Story

– reduced emissions and reduced fuel bills

Limescale is a major problem in terms of energy efficiency and savings in hard water areas – which account for more than 60% of the UK. It’s a primary cause of higher levels of emissions and higher fuel bills. Fact.

So finding a way of addressing the problem and at the same time helping to comply with the new Part L of the Building Regulations makes a huge amount of sense. This is where the SESI from Salamander Engineering can help.

There’s a frightening selection of physical water conditioners on the market for specifiers and installers to choose from including magnetic, electrolytic, electrostatic, electromagnetic and electronic. The reality is that the science simply doesn’t exist to prove these all work, and why, perhaps more worryingly, they appear to work well in one property and don’t in another, just down the road, with the same water mains and same water hardness.

Fit a unit that is proven

So if you’re looking to fit a water conditioner, you need to fit one that is proven and which has the science to back it up. In these circumstances, an electrolytic physical water conditioner – and one from a respected name in the water treatment sector – is the ideal choice. Even better if it’s proven to work, based on an independent study undertaken by the Cranfield University School of Water Sciences.

The SESI from Salamander, part of the Sentinel Group, works by flushing the hard salts through the system. It uses a zinc electrode and a natural electrolytic process to flush hard salts through the system rather than allowing them to settle and build up as limescale. It’s environmentally friendly and cost-effective operation has been proven in tests over the last 20 years. In simple terms, the crystals of hard salts in suspension change shape as they pass through the SESI and are unable to ‘stick’ to the metallic surfaces inside the pipes and radiators that untreated salts can – and do, alarmingly quickly. The process also ensures the crystals retain that shape and don’t quickly revert to the old damaging shape as soon as they have passed through the SESI unit.

Electrolytic physical conditioners such as Salamander Engineering’s SESI offer the ideal solution to the problem. They have the advantage of being able to protect an entire household’s pipe system from the formation of limescale encrustation, without the use of chemicals or salt and without the need for any electrical power supply. With no magnetic or chemical effect on the water, the units provide a cost effective and environmentally friendly solution. SESI is WRAS approved and fits in-line on the incoming main, providing whole house protection against limescale. The unit is non-magnetic, requires no chemicals, is non-polluting, maintenance free and comes with a 5 year guarantee.

As well as delivering an answer to the problems of hard water, the SESI helps specifiers and installers to meet the requirements of Building Regulations Part L cost effectively. Part L now clearly states that “where mains total hardness exceeds 200 parts per million, provision should be made to treat the feed water to water heaters and the hot water circuit to reduce limescale build up.” SESI offers an immediate and very convenient answer to this.

Limescale build up is damaging and is reducing the efficiency of customers’ appliances by up to 12%. Restoring optimum efficiency levels could save customers up to £100 a year on their energy bills – as highlighted by British Water.

The average life of a boiler heat exchanger – the element that actually heats the water flowing through it – is 10 – 15 years. But in hard water areas, this can dramatically decrease to just 2 – 3 years. However, if a specifier or an installer is knowledgeable about the hardness of the water and specifies or fits a limescale prevention device such as SESI, this rapid deterioration can be prevented and the heat exchanger should remain efficient for its full lifespan.

For more information on the SESI and all Salamander water treatment products visit www.salamander-engineering.co.uk, or call 01928 583280.

View Salamander's profile: